This is the long awaited and much anticipated F7 flight controller from Matek Systems bundled with the FCHUB-VTX.
F722-STD
Considering its size (36mm x 36mm) and weight (7g), there's a lot to like about this FC board. Offering the all important flight controller, barometer, gyro, OSD, SD slot, Blackbox, camera control, RSSI, and beeper, you're definetly getting your monies worth. And, with its impressive credentials, it handles exceptionally well.
There are sure to be quite a few drone racing pilots upgrading to this FC.
The F722-STD is designed to connect easily to both the the FCHUB-6S and the FCHUB-VTX, which is available separately. Click here for the FCHUB-6S.
FCHUB-VTX
Designed to work with Matek Systems F722-STD FC flight controller, the FCHUB-VTX is a neatly combined PDB and VTX in one.
The FCHUB-VTX itself has a height of only 7.5mm. Combined with the F722-STD, the two take up circa. 18.1mm, which is incredibly compact.
The F722-STD FC can be found clicking here.
Matek Systems Flight Controller F722-STD & FCHUB-VTX
Specification - F722-STD:
Brand name: Matek Systems
Item name: F722-STD flight controller
36x36mm PCB with 30.5mm mounting holes
Weight: 7g
MCU: 216MHz STM32F722RET6
IMU: 32K ICM20602 gyro/accelerometer (SPI)
Baro: BMP280 (I2C)
OSD: BetaFlight OSD w/ AT7456E chip
Blackbox: MicroSD card slot (SD/SDHC)
VCP, UART1, UART2, UART3, UART4, UART5
PPM/UART Shared: UART2-RX
Battery Voltage Sensor: 1:10
Current Sensor: No (FCHUB-6S, FCHUB-VTX option)
BEC 5V: No (FCHUB-6S, FCHUB-VTX option)
LDO 3.3V: Max.300mA
I2C1 SDA & SCL: Yes
Camera control: Yes
DAC: Yes
WS2812 Led Strip : Yes
Beeper : Yes
RSSI: Yes
Features - F722-STD:
3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
7x PWM / DShot outputs without conflict
5x UARTs
1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
1x I2C1
4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
1x Side-press button for BOOT(DFU) mode
1x 16pin bottom mounted FFC Slot for FCHUB-6S or FCHUB-VTX connectionSpecifications & Features - FCHUB-VTX
- Input voltage: 6~27V(2~6S LiPo)
- PDB: 4*30A (4*46A, 5 seconds)
- Current Sensor: 184A (Scale 179)
- BEC Output: 5V/1A for Camera or FC
- VTX: 40 standard 5.8G channels, A/B/E/F/R Band
- VTX Output Power: 25, 200, 500mW switchable
- Traditional button+LED control of frequency and power
- BFCMS (BFOSD & LUA Script) control via FC UART _TX
- Video signal & TX5 are ready on FFC connected with MATEK FC F405-OSD
- Silicon wires connection with other brands FC
- Firmware upgradeable
- VTX Power Consumption: 3.1W Max. @ 500mW
- Video Input Impedance: 75 Ohm
- Audio Subcarrier Frequency: 6.5 MHz
- RF Connector: MMCX
- Video Format: NTSC/PAL
- Weight: 14g (w/ MMCX whip antenna)
- Size: 36*45*7mm w/30.5mm mounting
NB 38CH firmware is preloaded now, E4(5645) & E8(5945) are locked. If you need full 40CH, pls flash it with firmware_V1.5
Package includes:
1x F722-STD flight controller
2x 0.5mm*16Pin 5cm Flexible Flat Cable
4x M3 Anti-vibration Standoffs1x FCHUB-VTX board
1x MMCX to SMA Female, RG178 cable 9cm
1x MMCX 5.8G whip antenna, RG178 8cm
1x Rubycon ZLH 35V/470uF Low ESR capacitor
SD Card (not included) Requirements: